Fisheye blog by The Idaho Painter

Fisheyes in Paint: Causes, Fixes & Prevention

•

Fisheyes in Paint: What Causes Them and How to Fix Them When Painting Cabinets and Interior Trim

By Chris Berry – The Idaho Painter | Paint Life Supply Co.

You've spent hours preparing your cabinets or interior trim. You've cleaned, sanded, primed, and finally started applying your finish coat. Everything looks great until you notice something strange happening in the wet paint.

Small circular craters begin appearing in your finish. The paint seems to pull away from certain spots, leaving little circles that refuse to cover no matter how much paint you apply.


Congratulations, you've just encountered one of the most frustrating problems in the painting industry: fisheyes.

Fisheyes can ruin an otherwise beautiful finish, especially when spraying cabinets, doors, baseboards, window trim, and other surfaces where a smooth, flawless finish is expected.


After more than 25 years in the painting industry, I've learned that understanding what causes a problem is just as important as knowing how to fix it.


Let's talk about what fisheyes are, why they happen, what to do when you see them, and how to keep them from ruining your next painting project.


What Are Fisheyes in Paint?

Fisheyes are small, circular defects that appear in a wet paint film when the coating pulls away from a contaminated area instead of flowing smoothly across the surface. They often look like tiny craters, rings, or circles with a raised outer edge. Sometimes you can see the previous coating or substrate in the center.


The problem is usually related to surface tension and contamination.


Paint is designed to wet a surface and spread evenly. However, certain contaminants have a lower surface energy than the surrounding surface, making it difficult for the paint to adhere and flow uniformly. Instead of leveling out, the paint pulls away from the contaminated area, creating the familiar fisheye appearance.


Common symptoms include:

  • Small circular craters in the wet paint.

  • Paint separating or pulling away from isolated spots.

  • Round defects that expose the primer or previous finish.

  • Multiple craters appearing immediately after spraying.

  • Defects that reappear even after another coat of paint.


Important: Not every crater is a fisheye. Air bubbles, solvent popping, pinholes, and poor atomization can produce similar-looking defects. Identifying the actual problem is the first step toward fixing it.

What Causes Fisheyes When Painting Cabinets and Trim?

The biggest misconception about fisheyes is that the paint itself must be defective.

While coating formulation problems can occur, many fisheye issues are caused by contamination somewhere in the painting process.


Here are the most common sources.

1. Silicone Contamination

Silicone is one of the most notorious causes of fisheyes, particularly when refinishing kitchen cabinets. Think about all the products that have been used in a kitchen over the years. Furniture polish, countertop cleaners, aerosol sprays, lubricants, and certain household cleaning products can contain silicone or other ingredients that interfere with paint adhesion. Silicone contamination can be extremely difficult to remove because even small amounts may cause the coating to pull away.

Common sources include:

  • Furniture polishes and shine-enhancing sprays.

  • Silicone-based lubricants.

  • Certain countertop and cabinet cleaning products.

  • Aerosol detailing products.

  • Residue from previous maintenance products.


The Idaho Painter Tip: Never assume that cabinets are clean just because they look clean. Years of household products can leave invisible contamination behind.

2. Cooking Grease and Household Oils

Kitchen cabinets are exposed to grease, cooking oils, and airborne contaminants for years. Cabinets near stoves, range hoods, and cooking areas are especially vulnerable. These contaminants accumulate on cabinet doors, frames, and detailed profiles. Sanding alone does not reliably remove grease. In some cases, sanding a dirty surface can spread contamination or embed it into scratches. This is why cleaning and degreasing should happen before sanding.

3. Wax and Furniture Polish

Wax is another common source of fisheyes. Older cabinets, furniture, doors, and interior wood trim may have been treated with wax-containing products. These products can leave a film that interferes with primers and finish coatings. Even if the surface has been sanded, residual wax can remain in wood grain, corners, profiles, and detailed areas. Applying more paint over the problem usually won't solve it.

4. Contaminated Compressed Air

This is an often-overlooked cause of fisheyes, particularly when using conventional spray guns or compressor-fed HVLP systems.

Compressed air can introduce contaminants directly into the coating.

 

Potential problems include:

  • Compressor oil entering the air supply.

  • Moisture accumulating in the air lines.

  • Contaminated hoses and fittings.

  • Inadequate filtration.

  • Oil or residue from pneumatic equipment.

When contaminated air reaches the spray gun, it can deposit oil or other substances into the wet paint film.

If fisheyes appear across multiple clean test surfaces, your air supply deserves immediate attention.

Remember: Turbine HVLP systems do not use a conventional oil-lubricated compressor, eliminating that particular source of compressor-oil contamination. However, dirty turbine filters, contaminated hoses, shop aerosols, and surface contamination can still create problems.

5. Contaminated Spray Equipment

Sometimes the contamination comes from your own equipment.

Spray guns, paint cups, hoses, and other components can introduce foreign materials into the coating.

Possible sources include:

  • Residual cleaning chemicals.

  • Incompatible lubricants.

  • Oil or grease from equipment maintenance.

  • Contaminated paint containers.

  • Dirty mixing equipment.

  • Residue left behind from previous coatings.

Keeping your equipment clean and following the manufacturer's maintenance instructions is essential.

6. Dirty Rags, Gloves, and Improper Handling

One of the easiest ways to contaminate a freshly prepared surface is through improper handling. Imagine spending hours cleaning, sanding, and preparing cabinet doors, only to wipe them down with a rag that previously contained furniture polish. You may have just reintroduced the exact contamination you worked to remove. The same problem can occur with dirty gloves, oily hands, or cleaning cloths containing residues from fabric softeners.


Use clean, dedicated materials for your final surface preparation.

7. Contamination From the Existing Finish

Sometimes the problem is already present in the substrate. Previous finishes, adhesives, waxes, oils, and other residues may interfere with your new coating system. This is especially common when refinishing older cabinets, furniture, doors, and stained woodwork. A surface can appear perfectly sanded and still contain materials that prevent proper wetting. That is why testing the coating system before spraying an entire kitchen can save you a tremendous amount of time and money.

What Should You Do When Fisheyes Appear While Painting?

This is where painters often make the biggest mistake.

They see fisheyes appearing in their wet paint and immediately try to fix them by applying more paint.


STOP! Do not keep spraying more paint over fisheyes.

Additional coats rarely eliminate active contamination. You may temporarily flood the craters, but the coating can continue pulling away, and excessive film thickness can create runs, sags, slow drying, and other problems.


Here is the process I recommend.

Step 1: Stop Spraying and Inspect the Problem

When you notice fisheyes, stop applying the coating to the affected area.


Look closely at the defect.


Is it happening in one isolated spot, or is it occurring across the entire cabinet door?

Are the fisheyes appearing on every door or only certain pieces?


Does the problem happen with every batch of paint or only one?


These questions can help you narrow down the source.


For example, if fisheyes appear only on cabinet doors near a kitchen stove, cooking grease or cleaning-product residue could be responsible.


If the problem occurs on every surface, including a new clean test panel, you may need to investigate the coating, spray equipment, or surrounding environment.

Step 2: Allow the Coating to Dry or Cure

Don't immediately start wiping or sanding wet paint unless the coating manufacturer provides a specific repair procedure.


In most cases, the best approach is to allow the affected coating to dry sufficiently before attempting repairs.


Follow the coating manufacturer's instructions for drying, curing, and recoating.


Trying to sand paint before it is ready can create a gummy mess and make the problem worse.

Step 3: Sand Away the Defective Finish

Once the coating is ready to sand, remove the defective material and level the surface.


Depending on the severity of the problem, you may need to sand back to the previous sound coating or primer.


If contamination has penetrated multiple layers, more extensive removal may be necessary.


Use an abrasive appropriate for the coating system and stage of repair.


Be careful not to sand through cabinet edges, profiles, or veneer.

Important: Sanding removes the visible defect, but it does not necessarily remove the contaminant that caused it.

That is why the next step is critical.

Step 4: Clean and Degrease the Surface Properly


Before recoating, remove the contamination.


Choose a cleaner or degreaser approved for the substrate and coating system.


Different contaminants require different cleaning methods.

For example:

  • Cooking grease may require an appropriate water-based degreaser.

  • Wax may require a compatible wax-removal process.

  • Silicone contamination may require a specialized cleaning procedure.

  • Residual cleaner must be thoroughly removed before recoating.

Follow the cleaning product's instructions, including rinsing when required.

Allow the surface to dry completely.

Avoid using random solvents without checking compatibility. Aggressive solvents can soften existing finishes, damage substrates, or create additional coating problems.

If silicone contamination is suspected, ordinary degreasing may not be sufficient.

Step 5: Test Before Repainting the Entire Surface

This is one of the most important steps.After cleaning and sanding, apply your primer or finish coating to a small test area. Use the same equipment, coating, and application technique you intend to use for the final job. Observe the coating as it wets the surface and begins to level. If the fisheyes return, the problem has not been eliminated.Do not proceed until you have identified and corrected the cause.

Step 6: Prime or Seal When Necessary

Some difficult surfaces may require a compatible primer or sealer after proper cleaning and preparation. This is especially important when refinishing older cabinets or trim with unknown previous coatings.


However, primer is not a substitute for removing contamination.


Even excellent bonding primers can fail when applied over silicone, grease, or wax. When dealing with persistent contamination, contact the coating manufacturer for a recommended cleaning, sealing, and recoating system.A successful test patch is essential before proceeding with the full project.

Step 7: Reapply the Finish Coat

Once the surface is clean, properly prepared, and your test application is successful, you can begin refinishing. Apply the coating at the recommended film thickness. Use the correct spray tip, fluid delivery, atomization settings, and application technique for your coating system. Avoid flooding the surface in an attempt to achieve a smoother finish. A clean substrate and properly applied coating are the foundation of professional results.

How to Troubleshoot Fisheyes When You Cannot Find the Cause

Sometimes the source of contamination isn't obvious.

This is when you need to troubleshoot systematically.

One of the most useful principles is to change one variable at a time.

Here is the sequence I recommend:

  1. Test the coating. Spray the same coating onto a known-clean, compatible test panel. If the fisheyes appear, investigate the paint, equipment, and environment.

2. Test the spray gun. Use a properly cleaned gun and cup. Check whether the problem disappears.

 

 

3. Check the air supply. For compressor-fed systems, inspect moisture and oil filtration. For turbine systems, inspect filters, hoses, and air intake conditions. Airless systems require attention to fluid-path contamination rather than compressed-air contamination.

 

4. Inspect the environment. Look for aerosol sprays, lubricants, silicone products, polishing compounds, or other contamination sources near the finishing area.

 

5. Test the substrate. Compare the suspect cabinet or trim with a known-clean test panel using the same coating and equipment.

 

Document your results. By isolating variables, you can identify whether the problem originates in the coating, application equipment, environment, or surface being painted. This is much more effective than changing everything at once and hoping the fisheyes disappear.

Should You Use a Fisheye Eliminator Additive?

There are products marketed as fisheye eliminators or anti-cratering additives. These products are designed to modify coating surface tension and improve wetting. In some compatible coating systems, they can help reduce the appearance of fisheyes. However, there are several important things to understand.

 

Fisheye eliminators do not remove contamination.

They may help the coating flow over a contaminated area, but the underlying contaminant can remain. That can lead to adhesion problems or other finish defects. Also, not every additive is compatible with every coating. This is especially important when working with modern waterborne cabinet finishes, urethanes, lacquers, and two-component coating systems. Never assume that a fisheye additive intended for one coating chemistry is safe to use in another.

 

Before adding anything to your paint:

  • Verify compatibility with the coating manufacturer.

  • Follow the approved mixing ratio.

  • Check whether the additive affects recoating or adhesion.

  • Perform a test application.

  • Confirm that it does not compromise the coating manufacturer's specifications or warranty.

 

My recommendation is to find and eliminate the contamination rather than relying on an additive to hide the problem.

How to Prevent Fisheyes When Refinishing Kitchen Cabinets

Preventing fisheyes starts long before you pull the trigger on your spray gun.

A professional cabinet refinishing process should include the following practices.

Clean Before Sanding

This is a big one. Never assume sanding will remove everything from a cabinet surface.

Remove grease, oils, waxes, and other contaminants before sanding so you don't spread them around.

Pay special attention to areas around cabinet handles, cooking surfaces, and frequently touched doors.

Use Clean, Dedicated Preparation Materials

Keep your cleaning towels, sponges, and equipment separate from materials used for polishing, waxing, or equipment maintenance.

Avoid contaminating the surface with oily hands or dirty gloves.

Keep Silicone Products Away From Your Spray Area

Silicone sprays, lubricants, and polishing products should never be used near active finishing operations.

Airborne contamination can travel farther than you might expect.

Maintain Your Spray Equipment

Clean your spray gun, paint cup, hoses, and filters according to the equipment manufacturer's instructions.

Make sure the coating and cleaning products are compatible with your equipment.

Control Your Finishing Environment

Keep your spray area clean and free from airborne contaminants.

Avoid using aerosol products nearby.

Use appropriate ventilation and filtration designed for the coatings being sprayed.

Always Perform a Test Application

When working with an unfamiliar cabinet finish or questionable substrate, test your coating system before beginning production.

A small test can prevent an expensive refinishing disaster.

Can Fisheyes Happen When Painting Interior Trim?

Absolutely.

Although fisheyes are frequently discussed in cabinet refinishing, they can also occur when painting baseboards, doors, window trim, crown molding, and other interior woodwork.

One common situation involves repainting previously finished trim in occupied homes.

Over the years, trim can accumulate:

  • Household cleaning-product residue.

  • Furniture polish overspray.

  • Wax from floor maintenance products.

  • Oils from hands and pets.

  • Silicone-based product residue.

  • Grease and other household contaminants.

Baseboards near hardwood floors can be particularly vulnerable to contamination from certain floor-care products.

Doors and trim around kitchens can accumulate cooking oils and grease.

If you begin brushing, rolling, or spraying over these contaminants, the paint may separate and create fisheyes.

The solution is the same: identify the contamination, remove it using an appropriate method, and test the coating before proceeding.

What If You Are Brushing or Rolling Instead of Spraying?

Fisheyes are not exclusive to spray applications.

They can occur when brushing or rolling interior trim as well.

If you notice small areas where the paint refuses to cover, resist the temptation to repeatedly brush over them.

Excessive brushing can create additional texture, drag marks, and poor leveling.

Allow the coating to dry as directed, prepare the affected area, remove the contamination, and test before recoating.

Remember, changing your application method will not necessarily solve a contaminated-surface problem.

Are Fisheyes and Paint Bubbles the Same Thing?

No. These defects can look similar, but they are not necessarily caused by the same problem.

Fisheyes Paint bubbles
Coating pulls away from an area Gas or air becomes trapped in the coating
Often caused by surface contamination May be caused by application, substrate, or drying conditions
Usually looks like a circular crater Often looks like a raised bubble
Can expose the underlying surface May collapse and leave a pinhole
Requires identifying wetting or contamination issues Requires identifying the source of trapped gas or air

A collapsed bubble can resemble a fisheye, so don't diagnose the defect by appearance alone.

Can You Just Paint Over Fisheyes?

Usually, this is a bad idea.

If the contaminant remains on the surface, another coat may develop the same problem. Even if the second coat appears to cover the craters, the underlying contamination may compromise adhesion. Professional refinishing is about more than making a surface look good immediately after spraying.

 

The finish needs to perform long after you leave the job.

The Idaho Painter's Final Thoughts: Don't Chase the Crater. Find the Contamination.

Fisheyes are frustrating, especially when you're trying to produce a flawless finish on expensive kitchen cabinets or high-end interior trim. But there is an important lesson here.

 

The solution isn't always in your spray gun, your paint, or your technique. Sometimes the problem is something you cannot even see.

Silicone, grease, wax, compressor oil, contaminated equipment, and household cleaning products can all interfere with the way a coating flows across a surface. When fisheyes appear, stop and investigate. Don't keep adding paint. Don't immediately blame the coating. And don't assume that sanding alone will solve the problem. Find the source of contamination, correct it, and test your finish before continuing.

 

The goal is not simply to make the fisheyes disappear. The goal is to create a durable, beautiful finish that your customer will be happy with for years.

 

Don't chase the crater. Trace the contamination.

Get the Right Tools for Professional Cabinet and Trim Finishing

At Paint Life Supply Co., we're dedicated to educating, empowering, and equipping painters worldwide.

 

Whether you're refinishing kitchen cabinets, spraying interior doors, or painting detailed trim, using quality equipment and proper preparation techniques makes a difference.

 

Visit PaintLifeSupply.com to explore professional painting tools, spray equipment, abrasives, and accessories designed to help you produce better finishes.

 

For more professional painting tips, tutorials, and real-world demonstrations, follow The Idaho Painter on Paint Life TV on YouTube.Paint Life – Educating, Empowering, and Equipping Painters Worldwide.

0 comments
Back to blog

Leave a comment